輸送帶由多層橡膠棉帆布（滌棉布）或滌綸帆布包覆或耐熱橡膠，經高溫硫化粘合而成，適用于輸送熱焦炭、水泥、礦渣和熱鑄件等，在使用期間不可避免會出現一些問題，下面來講解幾個方面。

The conveyor belt is made of multi-layer rubber cotton canvas (polyester cotton) or polyester canvas coated or heat-resistant rubber, which is vulcanized and bonded at high temperature. It is suitable for conveying hot coke, cement, slag and hot castings. Some problems will inevitably occur during use. Here are some aspects to explain.

輸送帶設備接頭質量不夠好：

The joint quality of conveyor belt equipment is not good enough:

山東輸送帶接頭涂膠的監督是輸送帶設備工藝流程中重要的環節。輸送帶由多層橡膠棉帆布（滌棉布）或滌綸帆布包覆或耐熱橡膠，經高溫硫化粘合而成，適用于輸送熱焦炭、水泥、礦渣和熱鑄件等。接頭的好壞直接影響運輸性是否異常。

The supervision of Shandong conveyor belt joint gluing is an important link in the process of conveyor belt equipment. The conveyor belt is made of multi-layer rubber cotton canvas (polyester cotton) or polyester canvas or heat-resistant rubber, which is vulcanized and bonded at high temperature. It is suitable for conveying hot coke, cement, slag and hot castings. The quality of the joint directly affects whether the transportability is abnormal.

硫化接頭質量問題導致的皮帶斷裂事故頻發，不僅影響生產，還造成人身傷害。接頭的質量體現在使用的后果上。如果在粘接過程中不加強臨時控制，僅通過竣工驗收很難看出問題。因此，在輸送帶設備的生產過程中，嚴格控制硫化接頭的質量是很重要的。

Belt breakage accidents caused by vulcanization joint quality problems occur frequently, which not only affect production, but also cause personal injury. The quality of joints is reflected in the consequences of use. If the temporary control is not strengthened during the bonding process, it is difficult to see the problem only through the completion acceptance. Therefore, it is very important to strictly control the quality of vulcanized joints in the production process of conveyor belt equipment.

輸送帶設備的長度不合適：

Improper length of conveyor belt equipment:

無論是新帶設備還是舊帶交換，如果當時整條輸送帶的設備規劃不正確，精心規劃，很容易造成傳送帶要加長。結果是配重（重錘式配重）撞到地面，導致起步打滑。確實當時沒有問題，試駕也沒有問題，只是設備處于低位。運行兩三個月后，啟動時配重下垂并著地。這是因為在設備過程中沒有考慮輸送帶的塑性變形和彈性變形。

Whether it is new belt equipment or old belt exchange, if the equipment planning of the whole conveyor belt is incorrect and carefully planned, it is easy to cause the conveyor belt to be lengthened. As a result, the counterweight (heavy hammer type counterweight) hit the ground, resulting in starting skid. There was really no problem at the time, there was no problem with the test drive, but the equipment was low. After twoorthree months of operation, the counterweight sags and lands on the ground during startup. This is because the plastic deformation and elastic deformation of the conveyor belt are not considered in the equipment process.

此外山東輸送帶設備實現后無需調試調整，新設備在未磨合時，輸送帶容易出現偏磨損。應特別注意漏斗調料板、裙板、擋板等的調整，防止輸送帶跑偏、卡死等現象。另外，要加強對輸送帶運行過程的監控，防止輸送帶因大塊物料的堵塞而造成適當磨損。

In addition, there is no need for commissioning and adjustment after the realization of Shandong conveyor belt equipment. When the new equipment is not run in, the conveyor belt is prone to partial wear. Special attention shall be paid to the adjustment of hopper seasoning plate, skirt, baffle, etc. to prevent the conveyor belt from deviation, jamming, etc. In addition, it is necessary to strengthen the monitoring of the running process of the conveyor belt to prevent the conveyor belt from being properly worn due to the blockage of large materials.

輸送帶接頭質量以及長度不合適的解決便是給大家介紹的問題內容，我們希望我們的介紹可以幫助您更好地工作，可以來關注我們的網站www.jsamsung.com.cn查看更多問題的解決方法。

The solution to the problem of improper joint quality and length of conveyor belt is the content introduced to you. We hope our introduction can help you work better. You can pay attention to our website www.huafengxiangsu Com for more solutions to problems.