使輸送帶更好的為我們的生產服務，下面我們就來說一個問題，輸送帶皮帶呈現打滑現象怎么處理？

To make the conveyor belt better serve our production, let's talk about a problem. How to deal with the slippage of the conveyor belt?

1、發動過快也會導致打滑。在這個時候，它能夠慢慢開始。如果采用鼠籠式電機，經過兩次微動后即可發動，也能有效克服打滑現象。

1. Starting too fast can also cause slipping. At this time, it can start slowly. If the squirrel cage motor is used, it can be started after two micro movements, which can also effectively overcome the slip phenomenon.

2、初始張力過小。皮帶離開滾筒處的張力不行，導致皮帶打滑。處理方法是調理張力設備，添加初始張力。

2. The initial tension is too small. The tension at the place where the belt leaves the drum is not good, causing the belt to slip. The treatment method is to adjust the tension equipment and add the initial tension.

3、如果山東輸送帶皮帶的負荷過載，超過電動機的負荷就會打滑。因此，打滑的有利一面是維護電動機。否則，長期運轉會燒壞電機。但對于手術來說，這是一次滑倒事端。

3. If the load of Shandong conveyor belt is overloaded, it will slip if it exceeds the load of the motor. Therefore, the advantage of slipping is to maintain the motor. Otherwise, long-term operation will burn out the motor. But for surgery, it was a slip.

4、尾滾柱軸承損壞不能轉動，或上下惰輪軸承損壞，轉動不太大。形成損壞的原因是飛機尾部漂浮下沉過多，損壞或不靈活的部件沒有及時修補和替換，添加了阻力，形成打滑。

4. The tail roller bearing is damaged and cannot rotate, or the upper and lower idler bearings are damaged and do not rotate too much. The reason for the damage is that the tail of the aircraft floats and sinks too much, and the damaged or inflexible parts are not repaired and replaced in time, adding resistance and causing slippage.

5、驅動滾筒與輸送帶之間的摩擦力不行，導致打滑。其不想要的狀況大多是輸送帶有水或環境潮濕。處理方法是在滾筒中參加一些松香粉。可是，不要用手吹設備。

5. The friction between the drive drum and the conveyor belt is not good, resulting in slipping. Most of the unwanted conditions are water in the conveyor belt or wet environment. The treatment method is to add some rosin powder in the roller. However, do not blow the equipment by hand.

我們在安裝或維修更換輸送帶的過程中，須控制好膠接后的輸送帶的總長度。須嚴格管理輸送帶膠接施工過程，抓好施工細節，確保接頭質量。更多相關內容就來網站http://www.jsamsung.com.cn咨詢了解吧。

In the process of installing, repairing and replacing the conveyor belt, we must control the total length of the conveyor belt after bonding. It is necessary to strictly manage the adhesive construction process of conveyor belt, pay attention to the construction details and ensure the quality of joints. Come to the website for more relevant content http://www.jsamsung.com.cn Consult and understand.