大多數輸送帶都是由向輸送帶制造商解釋帶的參數和特的參數和特點，都是環形輸送帶，安裝過程因連接方式而異。那么
山東輸送帶皮帶扣是如何安裝的？
Most of the conveyor belt is explained by the conveyor belt manufacturer belt parameters and special parameters and characteristics, are circular conveyor belt, installation process varies by connection mode. So how is the belt buckle of Shandong conveyor belt installed?
山東輸送帶皮帶扣是如何安裝的
Shandong conveyor belt belt buckle is how to install
鎖扣連接。鎖連接的輸送帶切割尺寸后，接頭通過鎖連接在一起。兩端的鎖通過鋼棒連接，拆卸方便，安裝簡單。因此，安裝時無需拆卸輥。兩側接頭對齊后，插入鋼棒。
Latch connection. After the conveyor belt connected by the lock is cut to size, the joints are connected together by the lock. Both ends of the lock through steel rod connection, easy to disassemble, simple installation. Therefore, there is no need to remove the roll during installation. After both joints are aligned, insert the steel rod.
熱硫化連接。熱硫化連接的輸送帶通過調整準確的溫度和壓力來實現連接。連接前，皮帶應進行齒工藝。生產的皮帶接口可承受較高的張力，外觀與皮帶的其他部分基本相同。這種連接方式產生的輸送帶具有外觀美觀、整體規則、接口張力強的特點。
Hot curing joint. The conveyor belt connected by heat vulcanization is connected by adjusting the accurate temperature and pressure. Before connecting, the belt should be toothed. The belt interface can withstand high tension, and the appearance is basically the same as the rest of the belt. The conveyor belt produced by this connection mode has the characteristics of beautiful appearance, overall rules and strong interface tension.
山東輸送帶皮帶扣注意事項？
Shandong belt belt buckle matters needing attention?
施工前，先把皮帶控制開關操作手把打到“零位”鎖死，并且掛牌“有人施工，嚴禁合閘”，設專人看。施工負責人安排人員對皮帶機打扣位置范圍內的雜物清理干凈，確保施工退路暢通。
Before construction, first hit the belt control switch operator handle to “zero” to lock, and the listing “there is construction, it is forbidden to close”, set a special person to see. The person in charge of construction shall arrange the personnel to clean up the sundries within the buckle position of the belt machine to ensure the smooth construction retreat.
打皮帶扣工作必須是在施工負責人的指導下進行施工作業施工時，施工單位必須有干部現場指揮，確保施工安全。
Belt buckle work must be carried out under the guidance of the construction person in charge of construction, construction units must have cadres on-site command, to ensure the safety of construction.
對更換皮帶接頭的工作，應先將需更換的皮帶接頭開到皮帶機中部，把皮帶放松，用兩付夾板卡住皮帶，卡住皮帶后，用手拉葫蘆進行緊帶，嚴集用點動或開動皮帶進行緊輸送帶。
For the replacement of belt joint, the belt joint to be replaced should first be opened to the middle of the belt machine, the belt is relaxed, the belt is stuck with two sets of splint, the belt is stuck, the belt is tightened with the hand hoist, and the belt is tightened with the point of movement or start.
Shandong conveyor belt belt buckle is how to install? The above content is related to the answer, if you have other questions to know, please come to our website www.jsamsung.com.cn for consultation.
聯系微信