縱向水波紋現象的出現不知道您見到過沒有？實際上該現象也會出現與傳送帶產品上，根據不同帶芯特性得知，在硫化時尼龍和EP布受壓后以平板中軸線為向兩邊延伸，當遇到墊鐵后無法擴展，這種情況下就會形成縱向水波紋。那么傳送帶出現縱向水波紋問題如何解決？

　　Have you ever seen the phenomenon of longitudinal water ripples? In fact, the phenomenon will also appear with the conveyor belt products, according to the characteristics of different cores, in vulcanization nylon and EP cloth compression to the plate axis as the center to extend to both sides, when the pad iron can not expand, in this case will form longitudinal water ripples. So how to solve the longitudinal water ripple problem of the conveyor belt?

　　生產時傳送帶寬度應小于成品寬度，并盡量保持在成品寬度的99%左右，硫化時應適當放寬模具寬度；硫化時適當增加壓力，一般增加2.5-3mpa左右；硫化時傳送帶的拉伸不宜過大，以1%-2%為宜，視帆布的熱收縮率而定。

　　The width of the conveyor belt should be less than the width of the finished product, and try to keep it about 99% of the width of the finished product, and the mold width should be properly relaxed when curing; When vulcanization, increase the pressure appropriately, generally increase about 2.5-3mpa; When vulcanizing, the stretching of the conveyor belt should not be too large, 1%-2% is appropriate, depending on the heat shrinkage of the canvas.

　　作為傳送帶，粘合劑的厚度比普通傳送帶稍厚，既可以防止出現質量缺陷，又可以增加層間的粘合力，特別是在高溫運行的EP芯帶，如果EP帆布膠合厚度不夠，在操作過程中容易造成膠與布或布與布脫層，但尼龍芯和帆布芯由于芯層硬度和柔軟度較低，很少出現。

　　As conveyor belt, the thickness of the adhesive is a little thick than ordinary conveyor belt, can prevent quality defects, and can increase the bonding strength between the layers, especially in high temperature operation of EP core zone, if the EP canvas agglutination thickness is not enough, easy to cause gum in the process of operation and cloth or cloth and cloth layer, but the godson and canvas core due to the low core layer hardness and softness, rarely appears.

　　山東傳送帶經常出現磨損、劃傷、破損、搭接部位開裂等問題，這些設備問題的出現不僅加快了傳送帶的損壞，而且造成物料的漏撒和浪費，通常出現傳送帶設備問題以后，企業都是通過縫補、加熱硫化或者報廢更新，這些方式都不能很好的解決設備問題，具體且有效的解決方法還是要去實踐，畢竟實踐出真理！

　　Shandong conveyor belt often appear wear, scratch, breakage, overlapping parts of the problem such as craze, problems arose with these devices not only accelerated the damage of the conveyor belt, and the cause of material leakage and waste, usually after the conveyor equipment problems, enterprise by sewing, heating vulcanization or scrapped, the method can well solve the problem of equipment, The concrete and effective solution is to practice, after all, practice leads to truth!

　　此外，如何選擇傳送帶也是一大解決方案，采購時要準確說明具體材料的名稱和性質，特別是粒度、溫度、是否有酸、堿等腐蝕性及特殊要求；指定具體應用，所需規格（寬度、長度、層數、厚度等），特別是耐熱傳送帶的使用溫度和體積。

　　In addition, how to choose the conveyor belt is also a major solution, procurement to accurately describe the name and nature of the specific material, especially particle size, temperature, whether there is acid, alkali and other corrosive and special requirements; Specify the specifications (width, length, number of layers, thickness, etc.) required for the specific application, especially the temperature and volume of the heat-resistant conveyor belt.

　　傳送帶出現縱向水波紋問題如何解決？以上便是問題的解答了，而且在此我們還講解了傳送帶其他方面的內容，希望能夠給您好的幫助，如果您想選購傳送帶進行工作的話，可以先來網站www.jsamsung.com.cn看看相關咨詢，了解了解相關的問題。

　　How to solve the longitudinal water ripple problem in the conveyor belt? The above is the answer to the problem, and here we also explain the conveyor belt other aspects of the content, I hope to give you good help, if you want to buy conveyor belt to work, you can first come to the website www.jsamsung.com.cn to see the relevant consultation, understand the relevant problems.