輸送帶之所以占有非常關鍵的位置。因為它不僅是牽引帶部分，還是滾動軸承部分，價格昂貴，約占所有連續輸送機成本的30%～50%。一旦輸送帶因磨損變軟，就會出現抗壓強度降低、使用壽命降低、皮帶跑偏等問題。下面
山東輸送帶廠家分析了幾種關鍵的磨損模式，并根據消耗的基本理論提出了一些維護措施。
The reason why the conveyor belt occupies a very critical position. Because it is not only the traction belt part, but also the rolling bearing part, which is expensive, accounting for about 30% - 50% of the cost of all continuous conveyors. Once the conveyor belt becomes soft due to wear, there will be problems such as reduced compressive strength, reduced service life, belt deviation and so on. Next, Shandong conveyor belt manufacturers analyze several key wear modes, and put forward some maintenance measures according to the basic theory of consumption.
進料槽與輸送帶磨損，進料槽與輸送帶接觸嚴密。它的設計方案和設備對輸送帶的磨損是非常有害的，是輸送帶磨損的關鍵方法。輸送帶在喂料過程中會損壞。當物料與輸送帶的方位角大于等于90度時，會對輸送帶造成嚴重磨損；為防止物料掉落，導板與皮帶過緊，造成皮帶磨損。
The feed chute and the conveyor belt are worn, and the feed chute and the conveyor belt are in close contact. Its design scheme and equipment are very harmful to the wear of conveyor belt, and it is the key method of conveyor belt wear. The conveyor belt will be damaged during feeding. When the azimuth angle between the material and the conveyor belt is greater than or equal to 90 degrees, it will cause serious wear to the conveyor belt; In order to prevent materials from falling, the guide plate and belt are too tight, causing belt wear.
帶有長夾雜物的硬塊粘在出口處，磨損或劃傷皮帶。為了減少進口輸送帶的磨損，進口的結構設計方案應考慮以下標準輸送帶和同向運行的輸送帶。在整個進料過程中，物料以與輸送帶完全相同的速度移動。
Hard lumps with long inclusions stick to the outlet and wear or scratch the belt. In order to reduce the wear of imported conveyor belts, the following standard conveyor belts and conveyor belts running in the same direction should be considered in the imported structural design scheme. During the whole feeding process, the material moves at exactly the same speed as the conveyor belt.
物料以小于1米的自落長徑比承載，然后對皮帶的沖擊盡可能小。進料溜槽裝有條形篩網，使粗料先落入輸送機，并顯示八角形緩沖區。有效溜槽和導向溜槽設計，防止物料落入皮帶；導槽擋板總寬度沿輸送帶方向越來越窄。此外，導槽應加寬到物料到達皮帶的速度。
The material is loaded with a self falling length diameter ratio of less than 1 meter, and then the impact on the belt is as small as possible. The feeding chute is equipped with a strip screen to make the coarse material fall into the conveyor first, and the octagonal buffer zone is displayed. Effective chute and guide chute design to prevent materials from falling into the belt; The total width of the guide baffle becomes narrower and narrower along the conveyor belt. In addition, the guide groove should be widened to the speed at which the material reaches the belt.
預防措施
preventive measure
輸送帶的選擇需要考慮很多因素，如：輸送帶輸送系統的相關要求；地形環境條件和安全的要求；輸送材料的類型、形式和特性，需要大帶寬、工作張力和輸送能力；滾筒小直徑；Gr嚙合和橫向剛度；載荷支撐；曲線和過渡段的長度；擰緊方。輸送帶的型式、行程、給料點及條件、運行周期；抗沖擊、抗撕裂、接頭條件等要求。
Many factors need to be considered in the selection of conveyor belt, such as: the relevant requirements of conveyor belt conveying system; Topographical environmental conditions and safety requirements; The type, form and characteristics of conveying materials require large bandwidth, working tension and conveying capacity; Small diameter of roller; GR meshing and lateral stiffness; Load support; Length of curve and transition section; Tighten square. Type, stroke, feeding point, condition and operation cycle of conveyor belt; Requirements for impact resistance, tear resistance, joint conditions, etc.
輸送部件基本上是標準設備。訂貨時，我們需要選擇的帶式輸送機廠家的產品。只有當輸送機制造商有良好的信譽，我們才能保證每個零件的準確性和質量。各部件的安裝應按照現行輸送設備安裝及驗收標準進行。對容易造成皮帶磨損的部位（如裙板、刮刀、各種清掃器等）應進行調整，以減少安裝時的磨損，并在運行中注意檢查。等等。
The conveying parts are basically standard equipment. When ordering, we need to choose the products of professional belt conveyor manufacturers. Only when the conveyor manufacturer has a good reputation can we guarantee the accuracy and quality of each part. The installation of all components shall be carried out in accordance with the current installation and acceptance standards of conveying equipment. Adjust the parts that are easy to cause belt wear (such as skirt, scraper, various sweepers, etc.) to reduce the wear during installation, and pay attention to inspection during operation. wait.
Here is a brief introduction to the conveyor belt. If you have any questions, please visit our website http://www.jsamsung.com.cn And leave a message for consultation. We will serve you wholeheartedly.
聯系微信